OLT (Optical Line Termination) is used in the Fiber network to distribute the internet with multiple connections using PON (passive optical network) and last-mile connection ONT (Optical Network Termination). If you are an internet service provider or you might use a Fiber network for your office and factory internet connection then this article is useful for you. This post will help you to Login the FTTH OLT web interface to set up the first time or later for PON and other configurations.
Although login steps for Syrotech Fiber OLT and any other brands are almost the same, only the login IP address is different from that also printed on OLT sticker. Fiber OLT unit is available from 2PON port, 4Port, 8 Port and 16PON port, and more. For uplink Ethernet gigabit and fiber 10Gb port available and can use as per connection type available wither fiber uplink or Cat6. Management port and console port available for configuration of SyroTech FTTH OLT, Consol port would use for command-line configuration and management port for configuring OLT from the web Gui interface.
The default login IP address and username password can differ for EPON OLT and GPON OLT that are usually printed on the sticker of the OLT unit.
You can use the default login Credentials for Syrotech GEPON and EPON fiber OLT as given below.
SyroTech OLT IP Address GPON / EPON– 192.168.8.100 or 192.168.8.200
Default username – admin
Syrotech OLT password– admin or Syro@43210$
You can find a sticker for default login credentials on your OLT bottom side as shown below sticker.
Product Name– SyroTch
Product Model– SY-GOPON-4OLT-L3
Right down login settings for your OLT and follow the steps to log in.
If you looking to access a new fiber OLT web interface for the first time then you must need a physical connection with your network and OLT. If your OLT device is already configured to network and you only looking to log in then you just connect the computer to the MGM port or uplink port.
Login and Setup SyroTech ONT/ONU Device
Open a web browser and access http://192.168.8.l00 or http://192.168.8.200 and wait to load the login page asking for username and password.
OLT URL- 192.168.8.100/action/login.html
OLT Web Management Interface
Username- admin
Password- admin
Verification code- (type the verification code to bo and press Login button)
You will land on the OLT status page where you can check all PON ports, Ethernet ports, and Fiber port up/down status.
The next and important step is to change the OLT default Login password for the first-time login.
You can directly click on the Change password option on the status page or also find the option under System settings.
Click Change Now button – (It is recommended to change your default password for this device for security and safety reasons.)
In the next step, you will get all user detail with role type.
User Table
Press the Edit button for the use you want to change the password as shown below image.
Username- admin
User Password– create a new password
Confirm Password– confirm the password to avoid any mistakes.
Press the Apply button and log in again with a new password.
Password change TIPs
Fibrsol Fiber ONT Reset if forget Password FiberSol FTTH ONT or XPON, GPON, or EPON…
Electroline ONT Login And Setup First Time Elctroline ONT or ONU login for the first…
BT-PON FTTH ONT Reset if Forget Password BT-PON ONT Modem last mile connectivity that installed…
192.0.0.1 Admin login router Default Gateway 192.0.0.1 for a router used to log in to…
192.168.1.7 Admin login Router Password The IP address 192.168.1.7 is a default login IP address…
How to Login Hitron FTTH ONT Modem Login Hitron Fiber ONT either GPON or EPON…
This website uses cookies.